Production Engineering - Medical Equipment Division

PEMED HOME 6035 E. 38th Avenue, Denver, Colorado 80207 USA (303) 393-7800 FAX (303) 393-1482

Dental

Dental CAD/CAM ceramic inlay system - $1,475

List: $56,900. MedCon: VG. Siemens Cerec 2, model 2791812 dental 'chair side' production unit for dental restoration. 115 V, 50/60 Hz. Software and the oral scanner are not included.

This is a 3 axis, x/y and rotation, small envelope CNC system.

Features:

• monitor, model 2796035; 7 x 9.25 inches, with response soft keys
• on-board fabrication chamber for inlays, crowns and veneers
• back chamber with wash bottle
• floppy disk drive
• on/off rocker switch with indicator light
• rear locking casters

Overall dimensions of the unit:

• width: 17.5 in.
• depth: 18.25
• height: 48.5

Shipping weight is about 240 pounds. 2 units in stock.

Foredom flex shaft power tool motor - $275

List: $390. MedCon: VG. Foredom Series DD flexible shaft power unit. 110-130 V, 60 Hz.

Features:

• motor with swivel mount on 6.5 x 5 inch base
• 42 inch shaft/sheath coupling assembly accepts handpieces listed in manual, drilling, sanding etc
• Foredom CFL-15 foot speed control
• includes flexible handpiece as shown
• power on/off rocker switch on motor housing
• Owner's Manual included; this shows the range of handpieces that may be used

Shipping weight is about 20 pounds.

Portable dental x-ray system - $2,375

List: $8,700. MedCon: G. Philips Oralix 65 mobile x-ray system. 120 V, 50/60 Hz. Needs aiming cone.

Features:

• 65 kVp, 7 mA tube; housing on swivel mount with angle indicator
• Philips Dens-O-Mat controller with exposure factor dials for patient type, film type, and oral regions
• rolling tripod base with locking casters
• power on/off rocker switch with green indicator light
• 13 foot power cord with hospital grade plug

Overall dimensions of the unit:

• base: 26 x 30in.
• height: 53.5 minimum; 69 typical use

Shipping weight is about 250 pounds.

Dental dust collector - $1,675

List: $2,600. MedCon: VG. Coe-Bilt model 444 Dust collector, 115 V, 60 Hz.

A high capacity dust collector for use in a central dust collecting station, which may be used to capture dental dust from ceramic grinding, or precious metals from polishing dusts and buffer exhaust.

Features:

• Baldor 1 hp motor (3450 rpm) and Cincinnati LM-6 fan
• twelve collection bags
• 3.5 inch inlet port
• two quarter turn latches each for the blower and collection access panels
• power on/off switch

Overall dimensions of the unit:

• width: 42.5 in.
• depth: 15.25
• height: 29

Shipping weight is about 400 pounds.

Centrifugal barrel finisher - $7,000

List: $22,700. MedCon: ex. Finishing Associates, centrifugal barrel finisher, model VC 12. 12 L total finishing capacity, using vibratory media, vibratory shot, abrasive sand and/or other media.

Features:

• used in dental labs, machine shops, jewelry finishing, medical and aerospace
• 4 octagonal barrels, 3 L each (0.1 ft.³)
• each barrel may be loaded with a different media
• unit mounted on retractable castors
• Variable speed, 0-250 rpm
• timer
• RPM speed display
• wired for 220 V AC, 60 Hz
• unit manufactured January, 2005
• may be used wet or dry
• applications include de burring of cast dentures, stamped or machined parts, polishing of dentures and dental work, surface hardening through tumbling, polishing and other forms of surface improvement
• 328 hours of use as shown on the hour meter

Shipping weight is about 700 pounds.

Dental chair with operatory - $3,750

List: $12,300. MedCon: EX. Adec Pro II dental chair (manufactured by Belmont). 120 V, 50/60 Hz.

Features:

• footswitch and three foot levers for programmed positions and auto return, adjustable back incline
• 100° left to right seat rotation
• steel baseplate, 22 x 22 inches
• articulating headrest
• swing away armrests
• dental operatory with instrument tray, drill connection etc.
• hygienist's station with air, water and suction
• spittoon with rinse spigot

Shipping weight is about 450 pounds.

Full dental station with operatory - $1,975 each

List: $156,000. MedCon: EX. 4 complete dental stations, consisting of dental chairs and operatories, made by Adec. A purchase of the contents of a large dental school.

Units are Adec model 1005 chair, with white base, and come with a free standing operatory delivery system.

Features:

• 5 white Adec chairs, with stand alone operatories
• all equipment in excellent condition, in full use before removal from service
• includes standalone operatories, as shown in photos
• power up, down and tilt back
• adjustable head support
• instrument for water and air dispensing
• one instrument holder built into side of operatory
• sling type arm rest
• power chair functions controlled through foot control

Dimensions:

• 19" seat width
• seat raises from 16.5 - 31.5 inches

Shipping weight is about 450 pounds each.

Panoramic X-ray unit - $2,875

List: $28,300. MedCon: VG. Planmeca PM 2002 CC maxillofacial X-ray unit. 110/117/220/240 V, 50/60 Hz.

Features:

• control panel has child/adult modes, positioning parameters and +/- touchpad buttons for setting mm, kV and mA
• X-ray tube with 80 kV max
• cassette holder
• description of panoramic procedure is printed on instrument
• mounting rail is 85.5 in. high
• unit new in 1990
• this model can be upgraded for use with the Planmeca Dimax digital sensor (see www.planmeca.com/index.php?page=63179&lng=1)

Shipping weight is about 350 pounds.

Dental chair and operatory - $1,975 each

List: $10,896. MedCon: VG. Chayes-Virginia Voyager dental chair, light and operatory.

Features:

• complete operatory including light on swivel arms with aiming handle, instrument tray, drill hook-ups, assistant's rinse and aspiration station
• 21 in. wide seat raises from 19 to 32 in. with footswitch control
• auto preset and return
• 1 handpiece connector is lighted
• seat cushion has a tear on base, can be reupholstered for an additional $275
• variable back recline
• articulated headrest
• 23 in. diameter base

Shipping weight is about 400 pounds. 4 units in stock.

Dental chairs, with exam light and operatories - $1,975 each

List: $6,275. MedCon: EX. Dental ease model JS dental chair with exam light. Electric over hydraulic lift operated.

Features:

• power up down
• chair raises from 13 inches to 27 inches high
• dental light has 4° of freedom, for easy patient positioning
• light is adjustable, with on off switch
• chairs have protective plastic plastic covering over leg support
• adjustable headrest
• 12 brown Dental ez chairs, with lights

Shipping weight for chair and light combination is about 400 pounds each. 12 matching units in stock.

Dental/ ENT emergency surgery chair - $2,975

List: $13,400. MedCon: VG. DMI model 220AIB treatment chair. 115 V, 60 Hz.

Features:

• 150 W three element lamp on adjustable swivel
• 19 in. wide seat
• seat/table raises from 19.5 to 38.5 in.
• left and right pressure on the footswitch pedals controls up and down for lift, back and tilt
• 20 x 35 in. base plate

Shipping weight is about 350 pounds.

Dental chair - $1,675

List: $8,600. MedCon: EX. Adec model 1005 chair, with white base and padded, flip way arms

Features:

• power up, down and tilt back
• adjustable head support
• flip away type arm rest
• power chair functions controlled through foot control
• wired for 120 VAC 50/60 hz

Dimensions:

• 18" seat width
• seat raises from 16 - 28 inches
• base is 26.5 x 33.5"

Shipping weight is about 400 pounds.

Air abrasion cavity prep system - $2,475

List: $9,200. MedCon: VG. American Dental Technologies KCP2000 air abrasion system120 V, 60 Hz.

Features:

• 7 foot flexible tubing and handpiece as shown
• selection of coarse/fine alumina abrasive agent
• footswitch controller
• handpiece holder
• transport handle

Overall dimensions of the unit:

• width: 17 in.
• depth: 21.5
• height: 30

Shipping weight is about 200 pounds.

Dental exam chair - $1,750

List: $5,930. MedCon: VG. Adec 1005 exam chair. 120 V, 60 Hz.

Features:

• footswitch with raise, tilt and preset positions
• 19 in. wide seat; seat height is adjustable from 17 to 31 in.
• arm rest with cuffs
• adjustable head rest

Overall dimensions of the unit:

• width: 26 in.
• depth: 57
• height: 39 min to 53 max

Shipping weight is about 250 pounds.

Face bow - $675

List: $1,900. MedCon: VG. Denar Slidematic facebow, model 200011-3. Used to locate maxillary dental and orthodontic castings in an articulator.

Measuring bow and transfer jig assembly as shown in photograph of apparatus packed in storage case.

Instruction manual included.

Overall dimensions of the case:

• width: 9.25 in.
• depth: 11
• height: 1.75

Shipping weight is about 5 pounds.

Dental UV curing light - $250

List: $585. Dentsply Caulk model 100.

Wired for 120 VAC, 60 Hz.

Shipping weight is about 20 pounds.

High speed alloy grinding/polishing machine - $375

List: $875. MedCon: VG. Grinding and polishing dental lathe, also called a high speed alloy grinder, Ticonium model 3165B1, 115 V, 60 Hz.

Excellent for carving, grinding and polishing.

Features:

• 3450 rpm high-speed
• quick release chuck
• Plexiglas shields
• connection provided for vacuum blower system or dust collector
• interior workspace light

Shipping weight is about 35 pounds.

Dental intra-oral camera system - $475 each

List: $9,200 each. MedCon: new. Celebrity intra-oral camera system, new in the box, by Welch Allyn. Units were made new in approximately 1995, and are unused for clinical use.

Features:

• built-in light source.
• high resolution optics
• cooling fan
• automatic brightness control providing a clear image
• electronics contained in control box, once inserted inpatient mouth has no electronics, optics only.
• optic one insert inpatient mount
• video output is composite video
• 12 volt DC power supply built into back.

Intra oral cameras are very useful for observing and documenting condition of patient's teeth. As pictures of teeth are displayed in real time on a television monitor, the patient and the doctor may discuss individual conditions of teeth and decide appropriate course of treatment. No other device allows a patient to easily and accurately see the same thing that the dentist sees. Also, video may be printed to a video printer (not included) and then submitted to an insurance company or other people for documentation.

The following pictures show some clinical views of teeth, which are degraded by the process of photographing a low quality video monitor with a digital camera. The actual images are much better than those shown below, and contain a great amount of useful information.

optical head shown in size relation to a penny

5 units in stock. Shipping weight is about 35 pounds. each. wired for 110 or 120 volts AC, 60 hertz.

Dental duplicator - $1,675

List: $4,250. MedCon: VG. Bego Gelovit MP dental duplicator. 110-120 V, 50-60 Hz. 900 W.

Features:

• on rolling wheels for easy access on floor or bench
• touchpad set of times and temperature programs
• LCD temperature display with ° C and ° F toggle
• drive shaft with three stirring arms
• pouring spout with opening lever

Overall dimensions of the unit:

• width: 12 in.
• depth: 13.5
• height: 23

Shipping weight is about 45 pounds. 5 units in stock.

Dental duplicator - $1,750

List: $4,825. MedCon: VG. CMP dental duplicator. 115 V, 60 Hz.

Features:

• LED temperature display with side bottom toggle
• time and temperature programming
• drive shaft with 2 paddles on a stirring arm in a clean mixing chamber
• Oriental Motor Co. model 51K40GNM-FCH-E1 induction motor ( 1500 rpm) and model 5GN60K-D8 gear head
• pouring spout with a dial-controlled opening
• power on/off rocker switch with indicator light

Overall dimensions of the unit:

• width: 17.25 in.
• depth: 20
• height: 27

Shipping weight is about 75 pounds.

Dental model trimmers - priced as shown

List: $1,675. MedCon: G. WhipMix model 3C 12 in. model trimmer. 115 V, 60 Hz.

Equipped as described in table below.

				model 3C, hose and base pan diamond abrasive wheel 1.5 hp GE motor, 3450 rpm	$750
				diamond abrasive wheel and hose, 1.5 hp GE motor, 3450 rpm	$750
				needs abrasive wheel appears to be 1.5 hp motor	$475

Overall dimensions of the unit:

• width: 17 in.
• depth: 19.5
• height: 18

Shipping weight is about 85 pounds each.

Dental model trimmers - priced as shown

List: $3,000. MedCon: G. Wehmer model trimmers.

Equipped as described in table below.

				diamond abrasive wheel GE 3/4 hp motor, 1725 rpm, 115 V, 60 Hz.	$575
				diamond abrasive wheel Marathon 2 hp, 3450 rpm motor, 115/208-230 V motor, 60 Hz.	$950
				needs abrasive wheel twin Dayton 2 hp, 3450 rpm motors, 115/230 V, 60 Hz.	$675

Overall dimensions of the unit:

• width: 20.5in.
• depth: 18
• height: 16

Shipping weight is about 60 pounds or 80 pounds for the unit with two motors.

Dental chair - $975 each

List: $6,200. MedCon: VG. Dentaleze model D-15925, with model "air foil" base.

Dentaleze dental chairs. Features:

• tilt back/head down position
• adjustable height
• adjustable head rest
• arm rests

5 units in stock. Shipping weight is about 300 pounds each.

Dental operating light - $750 each

List: $4,500. MedCon: G. Daray Lighting, Ltd. Proma dental operating light. 93-125 V, 50-60 Hz. Transformer has 12.5 V output. The model III arms are 57 and 32 in. in length.

Wall brackets are missing.

Shipping weight is about 60 pounds. 3 units in stock.

Vacuum porcelain furnace - $1,750

List: $3,175. MedCon: EX. NEY Sun Fire 10 programmable vacuum porcelain oven. Usually used to make dental porcelain materials, such as for dentures. 120 V, 50/60 Hz.

Features:

• digital display of temperature (degrees C/F option), step and time
• porcelain stage
• front controls include
  • platform raise
  • cycle programs and cycle start
  • touch pad program parameter entry
  • vacuum controls and purge cycle

Although not shown in photograph, includes a vacuum pump.

Overall dimensions of the unit:

• width: 15.5 in.
• depth: 13.5
• height: 22.5

Shipping weight is about 55 pounds.

Sandblasting cabinet - $750

List: $1,460. MedCon: VG. Cyclone Blasting Systems cabinet with gloves. 110 V.

Features:

• Plexiglas shield covers front access of 8 x 19 in.
• side opening of 12 x 17.5 in.
• light fixture with 110 V power cord over work area
• one glove has minor tear which is repairable
• three vents

Overall dimensions of the unit:

• width: 32.5 in.
• depth: 24.5
• height: 59

Shipping weight is about 180 pounds.

4 stage burnout furnace, 2300° F - $1,975

List: $4,700. MedCon: EX. 4 stage programmable oven, with a maximum temperature of 2300° Fahrenheit. Made by CMP/Ticonium industries.

features:

• electric muffle furnace
• stainless steel and and construction
• digital temperature control
• both door and top vents
• door observation port
• rheostat type control for quick, none programmable use
• wired for 220 V, 20 amps VAC
• 4 stage programmable controller, maximum ramp time of 99 hours per stage

Chamber dimensions:

• depth: 11"
• width: 9"
• height: 6.5"

Overall dimensions:

• length: 23
• width: 22
• height: 19

Includes operator manual, as photographed:

Shipping weight is about 125 pounds.

4 stage burnout oven, 2,000°F - $1,175

List: $2,220. MedCon: EX. 4 stage programmable burnout oven, for heat treating, lost wax casting, dental investment casting and other burnout oven applications. Radiance multistage furnace, made by Jelrus dental supply.

Features:

• Simple computer controller, with graphical front panel walk-through programming
• wired for 110 V AC
• 30 program capacity
• 4 stages
• vented top
• temperature range from ambient to 2000°F

controller has the following indicators:

• stage number (1-4)
• nighttime
• heat rate
• temp
• hold time
• degrees Fahrenheit/degrees centigrade
• hours and minutes time display
• rate display, degrees / minute

The following photo sequence shows entering a program with the following parameters:

• program number 23
• heating rate of 10°F per minute, in stage 1
• stage 1 target temperature, 600°F
• stage 1 hold time, 30 minutes at target temperature
• stage 2 heat rate, 20°F per minute
• stage 2 hold time, one hour
• stage 2 target temperature, 1600°F
• stage a three week rate, 20°F per minute
• stage three target temperature, 1600°F
• stage 4 heat rate,20° per minute

Typically, in lost wax casting, a drying temperature of 300°F can be used, then a Maxwell to melt or burnout temperature of 600 can be used, then 800°, then on up to casting temperature at between 1100°F, for testing sterling silver, on up to 2000° with high temperature investments, for other materials.

Also, the last stages of the cycle can be going from a high temperature, for example if stage two is 2000°, for glass work, then stage 3 could bring down to, for example 800°, hold for four hours to anneal the glass, stage 4 could bring the oven down to ambient temperature, or about 100°, and hold for an hour, until everything is cool,and stress relieved.

Chamber dimensions:

• length: 8"
• width: 5"
• height: 4.5"

Overall dimensions:

• length: 14.5"
• width: 13
• height 18.5

Shipping weight is about 75 pounds.

ReadyBath warmer - $275 each

List: $1,500. MedCon: VG. Quincy Lab/Medline ReadyBath MSC Warmer, model 10-140M. 115 V, 60 Hz. Warms ReadyBath line of patient wipes and cleansers to comfort temperature.

Features:

• heats to 120 degrees F
• indicator lamps for power on and heat cycle
• temperature gauge
• thermometer port or vent

Overall dimensions of the unit:

• width: 13.25 in.
• depth: 12
• height: 15.25

Shipping weight is about 45 pounds. 5 units in stock

ReadyBath warmer - $375 each

List: $2,375 each. MedCon: VG. Quincy Lab/Medline ReadyBath MSC Warmer 30, model 12-140MHS. 115 V, 60 Hz. Warms ReadyBath line of patient wipes and cleansers to comfort temperature.

Features:

• heats to 120 degrees F
• indicator lamps for power on and heat cycle
• temperature gauge
• thermometer port or vent
• product slots are approx. 4-5/8 x 9.5 x 1.25 in
• 30 unit capacity

Overall dimensions of the unit:

• width: 19 in.
• depth: 14.5
• height: 21.75

Shipping weight is about 50 pounds. 8 units in stock

Bench top dust collector - $175 each

List: 368 MedCon: VG. Handler model 76D-0 bench top dust collector for polishing wheel.

Features:

• working area of 28.75 in. W x 9.5 D can accommodate small polishing motor
• Pasco 1/15 HP motor rated for air movement of 365 CFM, 115 V, 60 Hz.
• two suction vents with holders for 10 x 12 x 2 in. reversible filters
• receptacle for two 60W incandescent bulbs to illuminate work area

Overall dimensions of the unit:

• width: 29 in.
• depth: 20.5
• height: 12.75

Shipping weight is about 50 pounds each. 10 units in stock.

Dental operatory cart - $375 each

List: $2,310. MedCon: EX. Dental operatory cart delivery system, for running dental hand pieces and intra oral drills.

Shipping weight is about 75 pounds each. About 20 units in stock.

Dental operatory cart - $375

List: $2,310. MedCon: EX.

Dental operatory cart delivery system, for running dental hand pieces and intra oral drills.

Shipping weight is about 75 pounds each. 10 units in stock.

Dental operatory cart - $375 each

List: $2,310. MedCon: EX. Dental operatory cart delivery system, for running dental hand pieces and intra oral drills.

Shipping weight is about 75 pounds each. 15 units in stock.

Dental operatory cart - $475 each

List: $2,310. MedCon: EX. Adec dental operatory cart delivery system, for running dental hand pieces and intra oral drills.

Shipping weight is about 75 pounds each.

Dental operatory cart - $475 each

List: $2,310. MedCon: EX. Adec model 2503 dental operatory cart delivery system, for running dental hand pieces and intra oral drills.

Shipping weight is about 75 pounds each.

Dental operatory cart - $475 each

List: $2,910. MedCon: EX. Adec Dental operatory cart delivery system, for running dental hand pieces and intra oral drills.

Shipping weight is about 75 pounds each.

Dental light - $875

List: $2,275. MedCon: VG. Adec model 6300 dental light. 120 V, 50/60 Hz.

Features:

• swivel arms of 33, 31, 29 and 13 in. have self-lubricating pivots
• uses 24 V, 150 W quartz-xenon-halogen bulb which can be set to low, medium and high intensities
• wall mount

Shipping weight is about 55 pounds.

Dental vacuum pump - $375

List: $945. MedCon: VG. Ney Super-vac pump, sized for dental vacuum furnace.115 V, 50/60 Hz.

Features:

• suction and exhaust ports
• oil drain on bottom
• quiet operation

Overall dimensions of the unit:

• width: 8 in.
• depth: 8
• height: 6

Shipping weight is about 20 pounds ea.

Dental vacuum pump - $375

List: $945. MedCon: VG. Penwalt/Jelenko Jelrus model P73 vacuum pump, sized for dental vacuum furnace. 115 V, 50/60 Hz.

Features:

• suction and exhaust ports
• oil drain on bottom
• quiet operation

Overall dimensions of the unit:

• width: 8 in.
• depth: 8
• height: 6

Shipping weight is about 20 pounds each.

Dental model trimmer - $350 each

List: $750. MedCon: VG. Chayes/Torit 320-A wet model trimmer. 115 V, 60 Hz.

Features:

• 10 in. wheel
• 1/3 hp, 1725 rpm GE motor
• bench mount brackets
• drain beneath pan
• water inlet coupling

Overall dimensions of the unit:

• width: 11.5 in.
• depth: 18
• height: 12.75

Shipping weight is about 40 pounds each. 2 units in stock.

Dental model trimmer - $350

List: $750. MedCon: VG. Handler Manufacturing Co. model 31 389 wet model trimmer. 115 V, 60 Hz.

Features:

• 10 in. wheel
• 1/3 hp motor
• swing open front housing
• bench mount brackets
• drain beneath pan

Overall dimensions of the unit:

• width: 12.5 in.
• depth: 12.75
• height: 13

Shipping weight is about 40 pounds.

Wax heating pots - $175 each

List: $325. MedCon: G. Nobilium heating pots with lids. 115 V. Heating control reads 0-500 degrees. Heating chamber is 8 in. diam. and 5 in. deep. One of the pots contains beeswax and the other has a clean chamber.

Shipping weight is about 25 pounds each. 2 units in stock.

Sand blaster - $975

List: $2,000. MedCon: VG. Jelenko whirlwind sandblaster with turbo-vac regenerative blower/dust collector. 115 V, 50/60 Hz.

Features:

• foot pedal
• glove box work area
• shielded top view of work area
• 2 canister holders on back
• blower is rated for air movement of 92 cfm at 60 Hz.
• occupies 40 in. bench space in side-by-side orientation or 17 in. with blower behind work cabinet

Shipping weight is about 95 pounds.

Dental lathes, polishers and mixers - $295 each

List: $650. MedCon: G.

	wing mix power mixer 1 in stock Shipping weight is about 40 pounds.
	wing mix power mixer 1 in stock Shipping weight is about 40 pounds.

Dental casting articulators - $975 takes all

List: $12,750. MedCon: G. Large quantity in pails 24 and 17 in. high. In the detail photograph the articulator on the left is marked Keystone and is the product in the large pail. The other articulator does not have a manufacturer's mark.

A good guess is approximately 150 to 200 articulators.

Shipping weight is about 210 pounds.

Burnout / casting oven - $750

List: $1,900. MedCon: F. Ticonium oven. 220 V. Furnace ceramic is cracked but useable. Includes Ticonium model 2000-A1 controller for casting machine/preheating oven. 115 V, 60 Hz.

Overall dimensions of the unit:

• width: 24 in.
• depth: 23.5
• height: 31

Dimensions of the heating chamber:

• width: 12 in.
• depth: 12
• height: 8.5

Shipping weight is about 200 pounds.

Dental investment vibrator - $175

List: $300. MedCon: G. Buffalo Dental model 200. 120 V, 60 Hz. This device vibrates flasks to remove air bubbles during the lost wax casting process.

Knob for setting variable speed. 7 x 10 in. platform.

Shipping weight is about 20 pounds.

Dental porcelain furnace - $675

List: $800. MedCon: N. brand-new in the box dental furnace, model 1300 made by Sybron Thermolyne.

Features:

• working interior is about a 4 inch cube
• ambient - 2,200 °F
• built-in analog pyrometer, readouts in both degrees C. and degrees Fahrenheit
• light weight fiber block low density ceramic insulation

Shipping weight is about 40 pounds.

Dental amalgamator - $325

List: $980. MedCon: EX. Caulk / Dentsply model Varimix III dental amalgamator.

Features:

• low/medium/high-speed
• 5-20 second timer
• covered mixing chamber

Panoramic dental x-ray - $1,975

List: $18,900. MedCon: VG. Toshiba/ Morita panoramic x-ray, model versaview. Takes full view x-ray shots of mouth in one sweeping pass, so that a complete exposure of all teeth may be made in one pass.

• unit new in May of 1987
• 0-10 ma
• 0-100 KVa
• with remote operator's control panel and trigger switch
• unit stands about 8 feet high
• may be run off of 50/60 Hz.

Shipping weight is approximately 550 lbs. each.

Dental operatory - $975

List: $2720. MedCon: VG. Adec model excellence dental operatory.

Unit is photographed on base, which is not part of unit.

Shipping weight is approximately 275 lbs.

Dental operatory - $850

List: $3,100. MedCon: G. Adec model Mini trol dental operatory unit. Includes four handpiece hoses, foot switch, and utility connections as shown.

Unit is photographed on base, which is not part of unit.

.	.	.
	.

Shipping weight is approximately 250 lbs.

Dental operatory - $1,275 each

list: $4,300. MedCon: VG. Adec dental operatory, with water reservoir, handpiece holder with five connections, extra handpiece holder with three positions, footswitch and utility connections as shown.

Unit normally attaches to wall or dental chair. Shown mounted on a pole, which is not included.

shipping weight is about 250 lbs.

Panoramic dental x-ray head and film holder- $975

list: $3,000. MedCon: G. units removed from known working dental x-ray system.

Consists of x-ray tube, support arm, and film holder, made by S&S white dental company.

Shipping weight is approximately 125 lbs. two units in stock.

Panoramic dental x-ray head and film holder - $675

List: $2,000. MedCon: G. units removed from known working dental x-ray system.

Made by S&S white dental company.

Shipping weight is approximately 70 lbs.

Dental film viewer / enlarger - $325

Dual film viewer / enlarger. Allows comparison of 2 dental films side by side, in enlarged format on 2 screens. Lights shines up through film, is collected by lens and projected on a rear view screen.

Screens are about 10" diagonal. Small films are enlarged on the screen so fine detail may be seen clearly by the dentist. may also be used for viewing microfilm, proofing transparencies, and enlarging detail on small areas of larger x-ray film.

Shipping weight is about 45 pounds.

Intra-oral camera - $475 each

List: $11,200. MedCon: New. Perspective I by Dentsply. Camera is a manufacturer's demo, with a video printer and monitor. System has less than 10 hours of use on it! Specifications: 5 mm to 100 mm focal range, up to 38x magnification, full screen, 250,000 pixel full color pictures, quiet, small, video printer has multi-format (16 on 1) and freeze-frame. System includes camera, hand piece and processor, 13" high resolution professional video monitor, new color video printer with new foot switch, video cables, new cart.

View box - $85 each

List: $180. MedCon: N. New in the box dental sized film viewers.

Wall mounted.

Shipping weight is about 20 pounds each. 3 units in stock

Dental head positioner - $275 each

List: $900. MedCon: EX. Dental head positioner, removed from panoramic dental x-ray chair. made by SS white. holds patients head for clear x-ray pictures.

Shipping weight is about 20 pounds. 4 units in stock.

Dental chair - $475

List: $7,200. MedCon: P. Table is sold as a repairman's special. Table powers up, does not respond to controls.

Cable is cut between foot control unit and chair. Elmed

Shipping weight is about 375 pounds.

Dental carts and operatories - $475 each

List: $1,500 - 3,000 each. MedCon: G.

1. Signature series, dental Ez
2. Adec
3. Adec
4. Denscoe concepts
5.
6. Dentech
7. Dectrol, by Adec

Shipping weight is about 150 pounds each. 1 of each unit shown in stock.

Dental lathe - $325

List: $900. MedCon: VG. Dental lathe buffer, with quick change chuck for quickly changing carving tools.

An excellent unit for carving, including dental materials, wood, lapidary, ceramic and glass.

Shipping weight is about 45 pounds each.

Ultrasonic scaler - $475 each

List: $1,375. MedCon: G. Densply model 1010m ultrasonic scaler. With cavitron ultrasonic generator model G38M. Features:

• water connection on bottom of unit
• wired for 50/60 Hz 110 VAC.
• adjustable power output
• adjustable water control
• with on/off footswitch.

Shipping weight is about 30 pounds each. 3 units in stock.

Dental drill on stand - $450

List: $1,300. MedCon: VG. Buffalo Emesco dental drill on stand. Arm has 5 pivot points, and 2 length adjustments. Unit is wired for 110 Vac, 50/60 Hz.

On stand with castors. Unit does not include variable speed foot control.

Shipping weight is about 45 pounds.

Dental chair - $1,275

List: $4,800. MedCon: G. Chayes Virginia model vision series dental chair.

Features:

• power up /down
• power slide forward and reverse
• power tilt back
• 4 pre-programmed chair positions with 1-touch button control
• stop button

		Position 1	Position 2
Position 3	Position 4 (discharge)

Wired for 120 VAC, 60 Hz. Shipping weight is about 300 pounds.

Dental operatory - $475 each

List: $2,100. MedCon: F. Signature series dental operatories, by Dentaleze and other manufacturers. Provide power, compressed air, water and suction to patients. Units are in usable but rough condition, missing small accessories (handpieces and probes). With connection hoses to connect to wall suction, water and compressed air.

Shipping weight is about 75 pounds each. 4 units in stock

Dental handpieces - $250 each

A) List: $530. MedCon: G. Air drive model 400 by Midwest dental, this head. 3 units in stock
B) List: $530. MedCon: G. Air drive model 400 by Midwest dental, thick head. 2 units in stock
C) List: $530. MedCon: G. Starflight. 1 unit in stock.

Dental chair - $1,275 each

List: $6,200. MedCon: EX. Dental Ez model VSR dental chair. Features:

• Electric up / down
• Electric tilt/back
• One button return
• Has both a foot control and switches built into back of chair
• Manual horizontal rotation
• Adjustable head rest

2 units in stock.

Cavitron scaler - $475 each

List: $1,900. MedCon: VG. Ultrasonic scaler, Dentsply model 2001.

Adjustable power and water supply, with foot control.

For cleaning and reparation of teeth. 2 units in stock

Amalgamator - $175 each

List: $750. MedCon: G. Torit amalgamator, by Chayes Virginia, model 611.

4 units in stock

List $770. MedCon: VG. Silamat amalgamator, by Williams Justi Ivoclar, model A.

Dental chairs - $975 each

List: $2,800 each. MedCon: VG. Ritter dental chairs, black upholstery on cream colored frame. Power adjustable height and tilt back.

Switches on both sides of chair back control:

• back up/down
• seal up/down
• 1 button return to normal

Also, the chair overall tilts and swivels manually.

© Copyright 1993 - 2010 by Production Engineering. PEMED® is a registered trademark of Production Engineering. MedCon is also a trademark of Production Engineering. All rights reserved. Contact PEMED for license requests. The usual copyright notices and disclaimers. Except for search engines or link listing, no part of this website, including derived information, may be republished without express written permission and payment of fees.

Production Engineering - Medical Equipment Division

6035 E. 38th Avenue, Denver, Colorado 80207 USA (303) 393-7800 FAX (303) 393-1482