Production Engineering - Medical Equipment Division

PEMED HOME 6035 E. 38th Avenue, Denver, Colorado 80207 USA (303) 393-7800 FAX (303) 393-1482

Surgical, surgery and exam tables

MRI-safe table - $1,375

List: $4,300. MedCon: VG. MRI-safe transport / imaging table

Features:

• for use as a transport gurney and imaging table in a MRI environment
• bi-partite pad, 73 x 23.5 x 1 inch
• adjustable back support, horizontal and three raised positions to a maximum inclination of about 70°
• four locking casters

Overall dimensions of the unit:

• width: 30 in.
• depth: 75
• height: 32 plus 1 inch pad

Shipping weight is about 140 pounds.

C-arm / pain management table - $7,500

List: $29,455. MedCon: EX. Durabuilt Medical motorized imaging table, model PMT8000 HLT. 120 V.

Features:

• carbon fiber diving board-style top
• 57 inch metal-free length for C-arm access
• 650 lbs distributed load capacity
• table height is adjustable from 27 inches (29.25 with pad) to 38.75 inches (41 with pad)
• 22.25 x 79.5 x 2.25 inch pad with head rest cutout
• hand-held remote has buttons for raise/lower table, right and left lateral roll (15°), and Trendelenburg (25°)and reverse Trendelenburg (15°) positions
• four locking casters
• 10-foot power cord with hospital grade plug

Overall dimensions of the unit:

• width: 23.5 in.
• length: 80
• height: 29

Shipping weight is about 350 pounds.

Surgical table, manual - $3,975

List: $12,300. MedCon: VG. Amsco 2080MIA surgical table. The MIA designation stands for manual controls, image analysis capable. The photograph set to the left shows the chair position, the table in the Trendelenburg position and the level table with arm supports attached. The pad upholstery is in good condition but shows some warp from storage. Inquire about replacement pads.

The reliable table of the profession.

Features:

• modular table consists of four platforms, kidney lift, head rest and additional fold-away extension at the foot end
• four radiolucent add-on platforms allow for X-ray cassette placement below reclined patient
• C-arm access to lower part of table; extension at foot end can serve as head support, allowing for patient to be placed in reverse orientation for C-arm procedures
• 20 inch wide table 19.5 x 38 x 2.5 inch pad
• hydraulic pedal adjusts table height from 27.5 to 44.75 inches (measured without pads or radiolucent platforms)
• hand crank controls back up and down, foot up and down, tilt to right and left sides, and flex position
• separate manual lever sets Trendelenburg and reverse Trendelenburg positions; degrees inclination indicator
• crank for kidney section lift
• siderails for adding attachments
• two arm support attachments with 3 inch pads; adjustable arc

The photographs show the chair with the radiolucent top boards removed, the kidney lift, the positioning controls, hydraulic lift and floor lock, the manufacturer's plate, and an animation of the different positions activated by the manual controls.

Shipping weight is about 800 pounds.

Surgical stool - $875

List: $2,300. MedCon: G. Stryker hydraulic stool (model EFA, catalog no. 763). Good seat upholstery and hydraulic action; good cosmetic condition except that decorative trim on T-bar has been removed and the stainless steel of the T-bar has some scratches.

Features:

• mobile stool on three-caster T-bar base
• 13-inch upholstered circular seat
• height adjustable from 21 to 31.5 inches; hydraulic and release levers
• a back rest could be added; slot and clamp present

Overall dimensions of the unit:

• width: 21 in.
• depth: 20
• height: 21

Shipping weight is about 45 pounds.

Patient support cushions - $375 each

rectangular	knee bolster

List: $1,700. MedCon: VG. Medtech positioning cushions for radiation oncology procedures. The base plate measurements for these are 20 x 12.125 x 10.5 inches for the model some on the left and 20 x 20 x 10.5 inches for the bolster shown on the right.

Shipping weight is about 5 and 8 pounds. 2 units of each model in stock.

The model called rectangular possibly accommodates elbows for immobilizing arms; it is not tapered for feet.

Fracture fixation table with accessories - $8,000

List: $33,170. MedCon: VG. Chick 702 orthopedic and surgical operating table.

Features:

• hydraulic pedal at head end adjusts trunk height from 37.5 to 46.5 inches
• complete set of 2.25 inch pads
• legs have adjustable spread angle and telescoping spars
• radiolucent upper body platform; C-arm access to upper body and extremities
• perineal post and sacral extension with radiolucent saddle board and pad
• crank rotates upper body platform laterally in a radial arc for traction
• three leg braces included
  • Bell foot brace
  • open frame brace (well leg)
  • Midmark model 22314 traction cuff
• rail for equipment and arm rest attachment
• additional accessories include
  • cross arm support
  • Bell foot piece 90° pin and wire holder, including fixation ferrules set (Chick 10778)
  • tibia extension and counter traction support
  • extra traction cuff
  • extra Bell heels
  • two extra pads
  • support belt and Lottes anklets

	view of pads and sacral support		cross arm support
	adjustable head rest crank to set lateral body traction		manufacturer's plate
	traction cuff		tibial extension, traction bars and countertraction support
	Bell foot brace		extra traction cuff and Bell heels
	well leg support		extra pads
	Bell foot piece 90° pin and wire holder inset shows fixation ferrules set		support belt and Lottes anklets

Shipping weight is about 350 pounds.

Surgical table - $9,000

List: $30,800. MedCon: VG. Midmark model 7100 surgery table. 115 V, 60 Hz. The photographs show the table in the lowered, raised and flex positions. The middle photograph also shows the set of raised radiolucent boards allowing for placement of a radiology film cassette.

Features:

• complete sets of attached (20.5 inch wide) and removable radiolucent boards and 2 inch pads
• electromechanical lift raises table height from 31.5 to 42.5 inches, plus pads
• positions adjustable by electromechanical actuator include Trendelenburg (28°), reverse Trendelenburg, leg raise (80°)/lower(105°), lower trunk raise/lower, tilt right and left (18°), flex and reflex
• various head rest positions are adjustable by release lever
• hand pendant and control panel at head end (please note that the hand pendant needs adjustment, so please allow three business days in your scheduling for us to complete this work)
• full length rails
• additional included leg supports can be substituted for leg board; adjustable angle and lateral extension for each leg (see photographs below)
• maximum patient weight, 500 lbs
• 18-foot power cord with hospital grade plug

The photographs show the use of the alternate leg supports in various orientations. Also shown is the hand pendant, table-mounted control panel and the manufacturer's plate.

Overall dimensions of the unit:

• width: 23.5 in.
• length: 78
• height: 33

Shipping weight is about 650 pounds.

Stirrups for surgical table - $575 set

List: $1,100. MedCon: G. "Candy Cane" stirrups for attachment to surgical table. Sold as pair. 16 mm x 84 mm length fitting to insert into compatible receptacle on surgical table or gurney. Clip for attaching ankle sling. Working height to clip is 19.5 inches.

Shipping weight is about 10 pounds. 2 pairs in stock

MRI imaging table - $3,975

List: $15,600. MedCon: VG. GE Signa imaging table. From a GE Signa MRI system, so this table is MRI compatible.

Minor abrasions to the transport handle; everything else is in good cosmetic and operating condition.

Features:

• concave patient cradle with longitudinal movement
• hydraulic petal raises cradle from 25.5 to 36.5 inches
• three-position side rails
• transport handle
• four locking casters
• docking hook

Overall dimensions of the unit:

• width: 24.5 in.
• length: 89
• height: 29

Shipping weight is about 300 pounds.

Pain management / radiolucent / c-arm compatible table - $3,975

List: $13,400. MedCon: VG. Skytron Beta X-ray table, model SB3200.

Features:

• offset frame allows easy C-arm access
• 24.5 x 76 inch bipartite table bed with Velcro fastener for pad
• hydraulic pedal at head end raises table height from 28 to 36 inches
• Trendelenberg and reverse Trendelenberg positions
• brake set at head and foot ends
• adjustable tilt back support
• slide down side rails do not interfere with C-arm access; can be removed if desired
• transport handle at head end
• retractable IV pole
• loops for restraint straps at waist and upper leg levels
• 8-inch easy-rolling castors
• 1995 manufacture
• new pad available, please add $300

Photographs showing Trendelenberg and reverse Trendelenberg positions, detail of the radiolucent platform, and use with a C-arm

Overall dimensions of the unit:

• width: 29.5 in.
• length: 80
• height: 30

Also available one unit with equipment rails instead of side rails (add $400)

Shipping weight is about 400 pounds.

Pain / C-arm imaging table - $3,275

List: $8,900. MedCon: VG. ADC Medical model ELH-200 x,y,z imaging table.

Features:

• 19.75 x 72 inch hinged radiolucent platform
• 2.5 inch pad conforms to body contour
• hydraulic lever raises platform hiding from 33.5 to 37.5 inches
• lateral and longitudinal platform movement
• spread base frame allows C-arm access
• four locking casters
• rebuilt longitudinal motion mechanism

The photographs show the movement control mechanisms and the overall good cosmetic appearance of the pad and table board.

Overall dimensions of the unit:

• width: 28.5 in.
• length: 75
• height: 33.5

Shipping weight is about 350 pounds.

Radiolucent pain/imaging table - $2,975

List: $7,300. MedCon: VG. Advanced Positioning Systems imaging table, manufactured by Krieger Medical.

Unit is fixed height.

Features:

• 84 inch long table, 22 inches wide
• 2 inch pad with head cut-out, Velcro fasteners
• transport handle at foot end

Overall dimensions of the unit:

• width: 30 in. (at base)
• depth: 86
• height: 38.5

Shipping weight is about 400 pounds.

Radiolucent imaging / pain table /patient gurney - $3,750

List: $6,700. MedCon: VG. Olympus Keymed Series 2 gurney.

Features:

• tri-partite platform (23.25 x 79 in.); both end boards lift (so patient can lay either way on table, and still have an adjustable back support)
• radiolucent table top and mat
• hydraulically adjustable bed height raises from 30 to 39.5 in.
• Trendelenberg and reverse Trendelenberg
• raise and lower foot pedals
• steer/free/brake bars at both ends
• slide down side rails
• iv pole can be put at any corner of the bed

Overall dimensions:

• width: 87 in.
• depth: 29
• height: 28.5

Overall dimensions of the unit:

• width: 32 in.
• depth: 87
• height: 31

Shipping weight is about 250 pounds.

Pain - C arm / endoscopy table - $3,750

List: $9,810. MedCon: EX. Olympus Keymed pain management imaging table. Features:

• radiolucent table top and mat
• hydraulically adjustable height
• normal / reverse Trendelenberg
• dual tilt back supports (so patient can lay either way on table, and still have an adjustable back support)
• dual collapsible side rails
• on castors
• tri-partite flexing radiolucent pad; 78 x 24 x 3 in.
• iv pole holder in each corner
• steer/free/brake bars at head and foot ends
• hydraulic pedal raises bed height (with pad) from 28.5 to 36 in.

Overall dimensions:

• width: 87 in.
• depth: 29
• height: 28.5

Shipping weight is about 300 pounds.

Surgical table - $13,750

List: $52,330. MedCon: VG. Maquet Alphastar Plus universal surgical table, model 1132.03B3. 115 V, 50/60 Hz.

Features:

• electrically-controlled hydraulic drive
• corded hand control for following positions
  • table up/down; 27 to 42 inches
  • up to 30° Trendelenburg and reverse
  • 18° lateral tilt
  • leg up/down
  • back up/down
  • flex
  • reflex
  • return to level
• two styles of extension boards for head end which can be used individually or in tandem for extra length or special positions
• four radiolucent boards for radiological procedures at any body level
• full length rails
• hand-held and below table controls (see photographs below)
• controls can be set for use with patient in standard or reverse orientation on the table
• 1000 lbs patient weight capacity
• electro hydraulic floor lock
• AC power or 24VDC battery operation
• universal power cord with hospital grade plug

The photographs show the stationary and hand-held controls, various modular extensions and an animation of the range of motions.

Overall dimensions of the unit:

• width: 23.5 in.
• depth: 76.5
• height: 27

Shipping weight is about 660 pounds.

Surgical table - $12,750

List: $55,600. MedCon: VG. Skytron Elite 6001 surgical table. 120 V, 60 Hz. Overall very good operating condition, but with some chipping of the enamel finish.

Features:

• 20 inch wide x 75 inch table length
• 180° top rotation
• corded hand control for following positions
  • table up/down; 28 to 43 inches
  • up to 30° Trendelenburg and reverse
  • 30° lateral tilt
  • leg up/down
  • back up/down
  • flex
  • reflex
• kidney lift crank
• three radiolucent platforms
• 2.25 inch thick pads included
• 500 lbs capacity
• full length rails
• electro hydraulic floor lock
• AC or battery operation
• universal power cord
• ships with new kidney lift crank handle

Shipping weight is about 600 pounds.

Surgical table - $2,975

List: $6,300. MedCon: VG. Amsco 1080 operation table. The photographs to the left show the chair position and the table position with the included pads.

Features:

• base (21 x 30 inches) rolls or sets on footpads with release pedal
• three part pads, 20 inch wide
• hydraulic pedal raises seat/table height from 27 to 45 inches (plus 2 inch pad)
• hand selectors and easy turn cranks set the following positions (shown in animation)
  • Trendelenberg
  • reverse Trendelenberg
  • lateral tilt to right and left
  • back raise/lower
  • foot raise/lower
  • kidney raise
  • flex
• accessories can be added; armrests to the rail, headrest to the back and footrest extension
• lateral tilt indicator

The photographic panels show the tilt and kidney lift positions, the manual position selector, hydraulic lift pedal, Trendelenburg angle selector, kidney lift crank, and an animation of the range of motions.

Overall dimensions of the unit:

• width: 71 in.
• depth: 27.5
• height: 29 .

Shipping weight is about 400 pounds.

Oral surgery / maxillofacial / ENT surgery chair - $4,475

List: $14,200. MedCon: VG. Boyd oral surgery maxillofacial and ENT surgery chair. Unit will ship with rebuilt vertical lift.

Features:

• chair swivels on base with locking lever
• 22 inch wide seat
• power up/down
• power tilt back support
• power chair tilt (Trendelenberg)
• seat raises from 20 inches to 36 inches high
• Trendelenberg (head down) position
• adjustable arm board, may be used for IV drip lines
• adjustable headrest
• surgical table side rails mounted on both sides of seat base and tilt back support
• emergency stop button
• tapered back of chair permits easy access to neck and head areas of patient
• connection for a hand held remote control, not included
• 1 AC outlet (for light or other equipment)
• foot control
  • levers control elevation, leg support up/down, back support up/down and tilt
  • step on buttons for three programmed table tilt position, normal/head down
  • return to home button
  • safety button
  • light control

Shipping weight is about 375 pounds.

Blood donation chair - $875

List: $2,250. MedCon: VG. Arlington Scientific Hampton lounge chair. One minor tear in fabric

Features:

• arm rest for blood draw is interchangeable between right and left sides
• gray Naugahyde/Naugaform covering with anti-bacterial and ant-fungal treatment
• rocker switch on back of unit activates recline mechanism
• 7-foot power cord with grounded plug

Overall dimensions of the unit:

• width: 24 in.
• depth: 70
• height: 52.5

Shipping weight is about 147 pounds.

Antique McManis manipulation treatment table - $3,750

List: $406. MedCon: VG. '20th Century Table' by McManus Table Company. AKA McManis table, depending on whose spelling you believe.

This is the original table, in working condition, circa 1930. This type of table holds our company record as the oldest medical item sold for its original functional intended use, in this case osteopathic manipulation. This record was set in 2012, when we sold a 1909 vintage McManis table for its original intended medical use. This is a true testament to the design of this table - that after 103 years, it is still the preferred way of doing a procedure.

Features:

• hydraulic crank for adjusting height
• adjustable spine lift
• adjustable tilt of upper and lower platforms
• lateral rotation of lower platform
• leather upholstery in good condition, although it is dry and stiff and has minor abrasions
• White matching the porcelain base (update, see below)
• before shipment we will replace base locking ring, which is cracked (as this part needs to be made, please allow about 7 business days for this work to be done)
• Table is 21 inches wide at trunk level, height is adjustable from 24.5 to 32.5 inches.

Shipping weight is about 300 pounds.

Adjustable height stainless instrument table - $750 each

List: $2,310. MedCon: VG. Phelan stainless steel table. Minor scratching of tabletop from usage and minor rusting of iron support bars.

Features:

• stainless steel table top, 34 x 42 inches
• pull chain and internal gear system allow raising table height from 38 to 61 inches
• easy rolling on 4 casters

Overall dimensions of the unit:

• width: 34 in.
• depth: 42
• height: 38

Shipping weight is about 90 pounds. 3 units in stock.

Kambin spinal frame - $875

List: $2,200. MedCon: VG. Kambin spinal frame. Support device designed to position spine during surgery. 19.1 x 28.75 inch radiolucent board with tapered pads 8 inches high in central region.

Shipping weight is about 15 pounds.

Epidural positioning stand - $1,375

List: $4,300. MedCon: VG. Valley Technology, Inc. Positioning device for epidural injections, mounted on labor delivery stand. For use with seated patient to securely support spinal access.

Features:

• apparatus rolls up to and locks in front of seated patient
• adjustable height and tilt face rest
• adjustable height and reach torso brace
• adjustable height patient arm rest
• adjustable height foot rest
• smooth rolling casters
• locking brakes set by easy release lever
• locking tether for securing to gurney or table

Overall dimensions of the unit:

• width: 20.5 in.
• depth: 31
• height: 57

Shipping weight is about 70 pounds.

Elevating therapy table - $975

List: $3,300. MedCon: VG. Ferno Ille Flexion 3000 physical therapy table. 120 V, 60 Hz.

Features:

• electric lift raises table height from 21 to 39 inches
• foot switch with up and down pedals
• tripartite padded boards, 27 inches wide, 76 inches overall length
• adjustable angle armrest
• adjustable tilt head support
• release lever allows adjustment of inclination of table platform section supporting lower trunk and legs
• locking front and rear casters
• 10 foot power cord with hospital grade plug

Overall dimensions of the unit:

• width: 77.5 in.
• depth: 28
• height: 21

Shipping weight is about 220 pounds.

Stainless steel table - $925 each

List: $1,700. MedCon: G. Stainless steel utility table. Manufacturer is not listed. 25 x 60 inch lipped top. Bottom shelf is tarnished.

Overall dimensions of the unit:

• width: 60 in.
• depth: 25
• height: 37.5

Shipping weight is about 120 pounds. 2 units in stock.

Surgical table - $4,500

List: $15,700. MedCon: VG. Smith + Nephew Surgi-OR Shampaigne 511 surgical table. Unit will ship with new leg support pad, leg railing and attachment fixtures.

Features:

• 20 inch wide stainless steel tripartite platform (62 inches overall length) with attachable headrest
• hydraulic pedal raises chair/table height from 28.5 to 39.5 inches (plus pad)
• hydraulic pedal sets Trendelenburg and reverse Trendelenburg positions
• release lever allows adjustable leg elevation and back support tilt
• 1.5" thick pad attached by Velcro strips
• includes 2 arm boards
• 21.5 x 31 inch base
• floor lock

Shipping weight is about 400 pounds.

Orthopedic surgical fracture table - $4,975

List: $27,600. MedCon: VG. Amsco Orthographic surgical table, model BE86-720-05.

Unit is largely C-arm compatible. Please add $450 for new pads.

Features:

• hydraulic table elevation to 47 inches
• 2.25 inch pads
• hand crank (removable) for setting Trendelenburg and reverse Trendelenburg positions
• hand crank (removable) for right and left tilt
• equipped with both padded leg support board (removable) and articulating leg equipment bars
• leg bars fold under table when not in use
• adjustable positioning of arm supports along railing
• slot for attaching perineal post
• 25.5 x 36 inch base
• floor lock
• accessories include a boot and the attachment fixtures for its variable positioning

detail photographs of the boot attachment and the swivel joints; animation showing various operational features

Shipping weight is about 450 pounds.

Orthopedic surgical table - $9,750

List: $83,800. MedCon: VG. Midmark Chick-Langren model 10500 orthopedic surgical and operating table.

Features and accessories:

• pump pedal raises top rail, 64 to 104 inches
• head and foot end release buttons set Trendelenberg (up to 10°) and reverse Trendelenberg (up to 20°) positions
• head and foot end floor locks
• upper body platform (17.75 inches wide) can be raised 3 inches by hand crank with respect to sacral slab
• lateral tilt control of upper body platform (15° right and left)
• leg spars extend 30 inches and rotate in an arc from front to back
• A-P cassette tunnel positioning board assembly
• radiolucent GM boards, compatible with mobile imaging systems
• rails at upper body position for attaching arm boards or other equipment
• slotted sacral slab
• traction controls on leg post (lengthen/shorten, abduct/adduct, and raise/lower/swivel)
• well leg support
• traction cuff
• perineal post
• front and rear attaching drapery rods
• horizontal iv pole with hangers
• top rail lock
• a variety of leg and other support platforms (see photos below)
• wedge pad
• restraint straps
• table care kit
• brochure, parts manual and technical manual

	upper body platform (adjustable height)		arm boards with pads of various thicknesses
	upper body platform (tilts right and left)		support mechanism for foot board
	hydraulic pedal foot and head release buttons height crank for upper body platform		perineal post
	crank for upper body platform tilt floor lock lever		pole with iv bag hangers
	AP cassette tunnel/ positioning board assembly		front and rear drapery rods
	traction cuff		wedge pad restraint straps table care kit
	well leg brace
	leg supports (heavily padded)		manufacturer's plate
	leg supports (lightly padded)		brochure and technical manual

Overall dimensions of the unit:

• width: 31 in.
• depth: 82
• height: 65

Shipping weight is about 900 pounds.

C-arm compatible orthopedic fracture table - $14,750

List: $96,000. MedCon: VG. Schaerer Mayfield model 10800 Chick IOT surgical table.

Features and accessories:

• radiolucent upper and lower body platforms, 17.5 inches wide at 28 inches high
• upper rail is at 63.5 inches and may be raised with the hydraulic pedal for C-arm access
• Trendelenberg and reverse Trendelenburg positions
• leg spars extend 19.5 inches and rotate in an arc from front to back
• traction controls on leg post (lengthen/shorten, abduct/adduct, and raise/lower/swivel)
• front and rear floor locks
• well leg support
• traction cuffs, 2 ea.
• perineal post
• top rail lock
• horizontal pole with iv bag hangers
• front and rear drapery rods
• leg brace
• three attachable rail segments
• rail clamp and support rod
• Radionics MRIA localizer frame, model MRIA-2-LF

	radiolucent boards		foot and calf support
	hydraulic pedal foot and head release buttons		rail clamp and support rod
	crank for platform tilt floor lock lever		front and rear drapery rods
	traction adjustments
	traction cuff		manufacturer's plate
	well leg brace		Radionics MRIA localizer frame (model MRIA-2-LF)
	pole with iv bag hangers

Overall dimensions of the unit:

• width: 32 in.
• depth: 82
• height: 63.5

Shipping weight is about 900 pounds.

Power procedure chair - $2,975

List: $7,400. MedCon: VG. UMF model 5020 power chair/table. 120 V, 60 Hz. Upholstery is an overall very good condition, but with one tear on patient's left side (see photograph).

Features:

• 26 inch wide seat
• seat height can be adjusted from 24 to 40 inches
• Linak actuator hand pendant has controls for table raise and lower, foot raise and lower, back raise and lower, tilt, and presets
• retractable stirrups and treatment pan
• adjustable headrest
• hygienic paper roll holder
• 22 x 34 inch base
• patient weight capacity, 400 lbs

Overall dimensions of the unit:

• width: 27 in.
• depth: 41
• height: 54

Shipping weight is about 300 pounds.

Portable OBGYN gynecology exam table - $1,750

List: $6,525. MedCon: VG. Retrofit Gynecart. This is a portable exam table with transfer pad that can be rolled to the end of a hospital bed or gurney and allows for a short-distance patient transfer onto a table with stirrups and examination light.

Features:

• rolling table with two front locking casters
• 31-inch foldout pad extends onto hospital bed or gurney
• halogen exam lamp on gooseneck, 12 V lamp operates from 120 V, 60 Hz. current
• stirrups with adjustable angle and spread
• pull out storage unit with four supply bins
• right and left doors have three supply bins
• one stationary shelf
• bracket for storage of physicians stool
• transport handle
• bottom bumpers

Overall dimensions of the unit:

• width: 40 in.
• depth: 25
• height: 36

Shipping weight is about 160 pounds.

Stirrups for surgical table - $675

MedCon: VG. Candy cane-style stirrups. Pair with leather loops as shown.

Shipping weight is about 10 pounds.

Treatment table - $275

List: $755. MedCon: VG. Sammons Preston ValueLine model 6901 treatment table.

Features:

• attractive blue vinyl upholstery with one minor tear (see photo) and one abrasion
• hinged back support board with head rest cutout and 3 inch padding can be set at horizontal or at 9 tilt positions to approximately 70°
• lower body support board has 2.5 inch padding
• solid wood legs

Overall dimensions of the unit:

• width: 30 in.
• length: 79
• height: 24

Shipping weight is about 120 pounds.

Surgical table leg brace - $475

MedCon: VG. OEC group leg brace. Support frame with five leg wraps with velcro fasteners. Tension strap with hook. 34.5 inches overall length.

Shipping weight is about 7 pounds.

Orthopedic surgical table boots - $1,475 the pair

List: $3,100. MedCon: N. Steris model ORT014A orthopedic boots. New, pair, adult size with clip for anchoring to traction device.

For use with a surgical or fracture table.

Overall dimensions of the shipping box:

• width: 9 in.
• length: 23.75
• height: 9

Shipping weight is about 10 pounds. 6 unit in stock.

Power exam /manipulation/ treatment table - $1,875

List: $3,470. MedCon: EX. Ritter model 106 power exam table. A large, flat and padded surface for treating patients.

Features:

24.5 x 72 inch surface padded to 3 inches

• electrically adjustable, up/down
• in excellent functional condition
• footswitch with raise and lower pedals adjusts table height from 23.5 to 38.5 inches above floor
• hygenic paper roll holder and retaining strap
• 6.5 foot power cord with hospital grade plug

Shipping weight is about 275 pounds.

Transport / endoscopy chair - $2,475 each

List: $9,600. MedCon: VG. Olympus OCC transport chair.

Features:

• 23.5 inch wide seat
• hydraulic pedals (both right and left sides) raise seat from 20 to 38 inches
• easy-grip release mechanism for conversion to bed position
• 330 lbs patient weight maximum (150 kg)
• brake/free/steer levers at both back casters
• retractable restraint pads at chest and waist level
• transport handle
• supply rack and gas tank holder
• footrest
• insertion ports for iv pole
• 1997 manufacture

Overall dimensions of the unit:

• width: 26.75 in.
• depth: 60
• height: 49

Shipping weight is about 180 pounds. 2 units in stock.

Truckload exam table sale - $375 each

List: 1,300. MedCon: G, VG. Exam tables. About what you would expect for features:

• pull out stirrups
• various colors (brown, red, blue, gray)
• pull out drawers
• some side storage
• pull out step at foot end of table
• some with built in power outlet

$375 each for the older style. We have about 6 tables in stock.

Shipping weight is about 275 or 300 pounds each. These may be shipped stacked.

Fracture table - $7,500

List: $29,400. MedCon: VG. Chick 703 orthopedic surgical operating table.

Features:

• hydraulic pedal at head end adjusts trunk height from 38.5 to 49 inches
• legs have adjustable spread angle and telescoping spars
• radiolucent upper body platform; C-arm access to upper body and extremities
• upper body platform can be unlocked to rotate laterally in a radial arc for traction
• three leg braces included
  • Bell foot brace
  • open frame brace
  • model 22314 traction cuff
• rail for equipment attachment
• slot for perineal post

Shipping weight is about 350 pounds.

Traction table - $1,875

List: $5,800. MedCon: VG. Chattanooga Mobilizer TME 3 traction table. 120 V, 60 Hz.

Features:

• table is 24.5 inches wide with 2.5 inch pads
• foot switch controls electric motor for Hi Lo down and up (table height from 26 to 35 inches) and lumbar down and up
• adjustable height arm supports
• adjustable tilt head support
• removable platform for traction machine attaches at foot end
• 9-foot power cord with hospital grade plug
• 2 AC outlets for auxiliary equipment

Overall dimensions of the unit:

• width: 24.5 in.
• depth: 95.5
• height: 26

Shipping weight is about 240 pounds.

Necropsy table - $975

List: $1,900. MedCon: VG. Stainless steel necropsy table with center drain and pipe thread below.

Overall dimensions of the unit:

• width: 43 in.
• depth: 25.75
• height: 32.5

Shipping weight is about 100 pounds.

Surgical table patient transfer rollers - $475 each

List: $900. MedCon: Ex. Patient transfer roller, 6 feet long. used to transfer a patient from a bed or gurney onto and off off a surgical table.

Made by Alimed and others. Shipping weight is about 30 pounds. 6 units in stock

Power exam/ OBGYN / Urgent procedure table with exam light- $3,275

List: $5,920. MedCon: VG. Hamilton 1K2 Image power procedure chair/table. 120 V, 60 Hz.

Features:

• 27 inch wide seat
• table height is adjustable from 26 to 42 inches
• 24 x 47 inch rolling base
• retractable stirrups
• ob-gyn tilt position
• Welch Allyn exam light with gooseneck
• pendant and footswitch with slide action controls for table up and down, tilt up and down, back up and down, foot up and down
• Trendelenberg and reverse Trendelenberg positions

Shipping weight is about 450 pounds.

Power procedure table - $3,975

List: $9,600. MedCon: VG. Midmark 411 power table. 115 V, 50/60 Hz. In excellent condition except missing lower leg pad.

Features:

• 27 inch wide seat
• table height is adjustable from 26 to 40.5 inches
• control panel has table up and down, tilt up (Trendelenberg) and return , back up and down, foot up and down, as well as programmed positions, emergency stop, and auto return
• adjustable headrest
• missing lower leg pad
• retractable stirrups
• ob-gyn tilt position
• treatment pan
• 23.5 x 33 inch base
• side rail for attaching and light or equipment

Overall dimensions of the unit:

• width: 27 in.
• depth: 35
• height: 58

W can provide a new lower leg pad for an additional $275

Shipping weight is about 450 pounds.

Urology exam table - $1,875

List: $5,800. MedCon: VG. Hamilton urology exam table. 120 V.

Shown on shipping pallet in our studio.

Features:

• 26-inch wide contoured exam table; 14 inch extendable pad covers treatment tray with drain
• table height adjustable from 25.5 to 30 inches
• pelvic tilt
• extendable and removable heel stirrups
• foot switch control for raise/lower table and raise/lower back support
• drawer and storage compartment with fold-down door
• hygienic paper roll holder
• two AC outlets
• 8 foot power cord with hospital grade plug

Overall dimensions of the unit:

• width: 26 in.
• depth: 60.5
• height: 27.5

Shipping weight is about 400 pounds.

Treatment table and stool - $375 the set

List: $575. MedCon: VG. WinCo. model 550 treatment table with Midmark 125-001 practitioner's stool.

Features:

• 6 foot long table, French blue vinyl with PermaBlock antibacterial coating
• patient support roll
• hygienic paper roll holder
• 16 inch diameter stool on five casters is adjustable from 18 to 25 inches high

Overall dimensions of the unit:

• width: 27.5 in.
• depth: 72.5
• height: 30

Shipping weight is about 120 pounds.

MRI table - $1,375

List: $2,275. MedCon: VG. Biodex MRI table, model 240-100

Features:

• aluminum construction, nonmagnetic
• 25 x 72 inch table, 33.5 inches high
• four locking castors
• 350 lbs capacity
• restraint strap
• collapsible side rails
• Velcro strip for securing pads

Shipping weight is about 260 pounds.

OR table top with carrier - $2,750 each

List: $12,900. MedCon: VG. Stierlen-Maquet table (E-Nr. 1001.55)

Features:

• 19.5 x 84 inch long table at 38 inches high
• leg supports can be adjusted individually
• hand crank sets the back support tilt
• spinal tilt
• Trendelenberg and reverse Trendelenberg positions
• four locking castors
• front handle to aid in positioning

photographs showing the cushion, back support crank and the locking mechanisms

Shipping weight is about 300 pounds. 3 units in stock.

Ophthalmic surgical power chair - $2,750

List: $10,720. MedCon: VG. ORL Systems ophthalmic chair. 110 V.

Features:

• seat raises from 23 to 32 inches
• swivel and lock levers
• back tilt release lever
• arm rests can swivel out to mount position
• adjustable head rest
• foot rest
• 11 foot power cord with grounded plug

Overall dimensions of the unit:

• base: 22 x 32 in.
• height: 56

Shipping weight is about 300 pounds.

Power OBGYN / minor surgery procedure table - $1,375

List: $3,200. MedCon: G. Ritter model F procedure table.

Features:

• power up/down elevation
• power tilt, head down (Trendelenberg)
• adjustable headrest and adjustable extension
• foot pedal
• manual horizontal rotation
• hideaway stirrups
• hideaway groin area fluid pan

When low to the ground, table is low enough to easily accommodate a patient getting in a wheelchair. (about 20 inches).

Shipping weight is about 300 pounds.

Power procedure chair - $1,100

List: $2,700. MedCon: VG. Reliance 5000 power procedures chair. 115 V, 60 Hz.

Features:

• 19 inch wide seat
• foot switch with up and down peddles activate electromechanical mechanism to raise chair from 20 to 29.5 inches
• swing out armrests
• release lever on back as chair declines back support to near horizontal level
• adjustable head rest
• foot rest
• 9-foot power cord with hospital grade plug

Overall dimensions of the unit:

• width: 24.5 in.
• depth: 26
• height: 51.5

Shipping weight is about 250 pounds.

Power procedure chair - $975

List: $2,100. MedCon: VG. Brewer Z650 power procedures chair. 115 V, 60 Hz.

Features:

• 20 inch wide seat
• raise and lower pedals; electromechanical lift raises seat from 22 to 30 inches
• armrest lifts back
• release lever allows variable back support positioning
• adjustable height headrest
• footrest
• 6.5 foot power cord with hospital grade plug

Overall dimensions of the unit:

• base: 23 x 28 in.
• height: 49.5

Shipping weight is about 250 pounds.

Cosmetic / obgyn/ uro / exam / procedure table - $1,750

List: $8,300. MedCon: inc. Ritter examination/chair, no model number. 115 V, 50/60 Hz.

Unit is missing one pad as shown.

Features:

• adjustable back and foot platforms allows positioning as upright chair, back reclined chair, flat table, Trendelenberg table
• 24 in. wide seat raises from 27 to 42.5 in.
• can be outfitted with stirrups
• footswitch built into base operates by lateral pressure
• 23.5 x 36 in. base

Shipping weight is about 300 pounds.

Knee / foot rests - $975 each

List: $1,900. MedCon: VG. Set of two knee or foot rests for surgical table, unknown manufacture. Padded rest is 15 x 7 inches. Adjustable height bar has flat edge for clamping.

This is for sale packaged with one of our surgical tables.

Shipping weight is about 8 pounds each.

Orthopedic surgical fracture table - $5,750

List: $$47,600. MedCon: VG. Amsco model Orthographic II orthopedic fracture table.

Features:

• spreadable traction bars with leg holders
• hydraulic pedal adjusts height from 29 to 46 inches
• hand crank sets Trendelenberg and reverse Trendelenberg positioning up to 15°
• hand crank sets lateral tilt up to 15°
• mobile unit with lock pedal
• compact storage position
• rails for attaching accessories

Exterior dimensions:

• length: 64"
• width: 28"
• height: 31

Shipping weight is about 600 pounds.

Hydraulic patient transfer chair / bed - $2,375 each

List: $9,800. MedCon: EX. Steris Hausted APC (all purpose chair). This is the hydraulic version of the power chair we have at $2,975.

Features:

• 22 inch wide seat
• hydraulic foot pedal raises height from 27 to 34 inches
• slide-down arm rests
• removable IV pole which stores in clips on base
• push bar/ transport handle
• break/neutral/steering castors
• recline/Trendelenberg lever
• flip away foot rest
• restraint strap
• 2 in. cushion with lumbar insert and head support
• gas tank holder

Overall dimensions of the unit:

• width: 26 in.
• depth: 40
• height: 54

Shipping weight is about 250 pounds. 3 units in stock.

Power exam/OBGYN/ minor surgery / cosmetic procedure table - $2,975

List: $5,300. MedCon: VG. Hamilton 1K4 power exam table. 120 V, 60 Hz.

Has minor upholstery damage, this can be reupholstered for an additional $450.

Features:

• chair/table with transport frame; chair can be removed from frame
• 29 inch wide seat
• height adjusts from 25 to 42 inches
• stirrups and treatment pan
• adjustable head rest
• foot switch with side action levers
• two auxiliary AC outlets
• 9 foot power cord with hospital grade plug
• hygienic paper roll holder

Overall dimensions of the unit:

• width: 49.5 in.
• depth: 29
• height: 58

Shipping weight is about 450 pounds.

Surgical table - $12,750

List: $56,700. MedCon: VG. Amsco Quantum 3080 sp surgical table. 120 V, 50/60 Hz.

Features:

• seat / table height is adjustable from 31 to 48 inches
• 2 inch pads
• support boards are 20 inches wide
• side rails on all sections
• tilt of the headboard can be adjusted manually with lock and release mechanism
• AC and battery power
• auxiliary control panel with toggle switches for Trendelenberg, height, side tilt, back and leg
• hand control has above positions as well as flex, reflex and patient orientation
• ships with new hand control, batteries, leg and lower torso boards

Shipping weight is about 800 pounds.

Stereotactic imaging / radiation treatment table - $6,475

List: $35,000. MedCon: VG. Varian Med-Tec exact indexed immobilization system.

This unit accurately positions patients for radiation therapy planning and oncology treatment.

Features:

• mobile unit with four locking casters, wooden storage bin and drawers, transport handle and metal support frame
• carbon fiber couch top
• imaging table is 36 inches height, 18 inches wide and 75 inches long
• two semi-circular arcades with equipment attachment ports
• x, y and z stereotactic positioners with micrometers; battery powered digital display of locations, +/- 0.1 mm accuracy
• removable patient grips
• additional Lok-Bars, rods and positioning accessories as shown in the photographs

photographs showing a detail of the carbon composite table and the included Lok-Bars, rod and other accessories

Overall dimensions of the unit:

• width: 25 in.
• length: 84
• height: 38

Shipping weight is about 300 pounds.

Chiropractic flexion table - $1,750

List: $6,200. MedCon: G.

Chiropractic flexion table, unknown manufacturer. Some rusting of the steel; some chipping of painted base.

Features:

• 25.5 inch height including 3.5 inch pads
• padded headrest with adjustable upward and lateral tilt
• patient footrest bar
• practitioner's footrest bar at the head end
• three pedals to set tilt of padded segments
• bottom two segments can be locked in a tilt down positions
• heavy 18.5 x 40.5 inch base

Shipping weight is about 350 pounds.

C-arm/ nuclear/ imaging table - $2,750

List: $16,350. MedCon: VG. Summit Nuclear Vision 1024 table. 115 V, 60 Hz.

Features:

• cantilevered carbon fiber resin table; C-arm compatible
• 300 pound load
• cm markings along table length
• transport handle
• position lock lever and release
• cable is included for interface with nuclear medicine camera
• table accessories included (see photos below)

Overall dimensions of the unit:

• width: 23 in.
• length: 90
• height: 32.5

Shipping weight is about 500 pounds.

Therapy table - $1,750

List: $6,350. MedCon: VG. Chattanooga Mobilizer model TME 3. 120 V, 60 Hz.

Features:

• table is 24.5 inches wide
• table raises from 26 to 35 inches high
• lumbar center slides back 6 inches
• adjustable head and arm supports
• foot switch with 5 foot cable for lumbar raise and high/low
• two locking casters
• 7 foot power cord with hospital grade plug

Overall dimensions of the unit:

• width: 24 in.
• length: 67
• height: 35

Shipping weight is about 236 pounds.

Traction table - $1,375

List: $3,800. MedCon: VG. Chattanooga Triton TRF-22 traction table

Features:

• bipartite platform; 24.5 inches wide with 35 and 40 inch long sections
• includes mounting platform for traction machine
• spine elevation knob
• includes Triton trs-30 practitioner's stool (12.5 x 21 inches; adjustable height. 13.5 to 19.5)

Overall dimensions of the unit:

• width: 24.5 in.
• length: 96
• height: 30

Shipping weight is about 134 pounds.

Treatment or traction table - $975

List: $4,300. MedCon: VG. Chattanooga Triton TRF-22 treatment and traction table.

Features:

• 24.5 inch wide table platforms, 35 and 40 inches long
• spinal lift knob
• upholstery in good condition with one minor tear

Overall dimensions of the unit:

• width: 24.5 in.
• depth: 75
• height: 30

Shipping weight is about 105 pounds.

Traction and therapy table - $875

List: $2,300. MedCon: VG. Tru-Eze Manufacturing, Inc. Tru-Trac table, model RT-99 chiropractic treatment table.

Features:

• upholstered table with 5 support legs

• platforms pull apart 4.75 inches, release and lock lever
• upholstery in good condition with some minor stain spots

Overall dimensions of the unit:

• width: 24 in.
• depth: 74
• height: 31

Shipping weight is about 144 pounds.

Neuro surgical instrument table - $1,750

List: $6,300. MedCon: VG. Phelan model 3-0004 neuro surgical instrument table.

Features:

• can be positioned over surgical table for deploying heavy neuro surgical instruments
• 48 x 32.5 inch stainless steel top work surface
• hand crank for height adjustment
• all stainless steel construction

Overall dimensions of the unit:

• width: 48 in.
• depth: 32.5
• height: 47

Shipping weight is about 300 pounds.

Andrews spinal surgical table - $9,750

List: $37,900. MedCon: G. Andrews spinal surgical table, made by OSI. Used for patient positioning and fixation during spinal surgical procedures. type SST 3000, model 5820.

Features:

• operated by hydraulic foot pump
• normal/reverse Trendelenberg
• table height up/down
• torso lift, up/down
• foot end, up/down
• lateral tilt, patient's right or left
• tibial support, up/down,
• table top height varies from 28.5 inches to 39 inches
• 350 pounds patient capacity
• C-arm compatible, in both AP and lateral intra operative views
• patient may be kept in face down prone, or face down kneeling position

Includes the following pads and accessories:

• iliac crest supports
• pads and small accessories, as shown
• storage cover

Shipping weight is about 400 pounds.

Surgical table extension - $1,375

List: $5,820. MedCon: VG. Matthews surgical table extension platform. Fits A skytron 6500 series table, and others

Features:

• frame and pad are 34 inches long and 26 inches wide tapering to 16 inches wide at connection to surgical table rail
• removable pad insert; 12 x 18 inches
• adjustable height support leg with locking extension rod

Shipping weight is about 30 pounds.

Autopsy table - $4,475

List: $16,700. MedCon: VG. Lipshaw model LM3B autopsy table. 115 V.

Features:

• stainless steel table on central pedestal
• twin sinks with faucet for hot and cold water and spray hose
• center drain with disposal
• four body support panels (see right photo above)
• perimeter rinse piping fits inside table rim
• knobs for table spray and table rinse
• 2 AC outlets

Overall dimensions of the unit:

• width: 30 in.
• length: 105.5
• height: 36

Shipping weight is about 600 pounds.

Oral / ENT/ Dental surgical chair - $2,750

List: $9,800. MedCon: G. Reliance DMI-219 power procedure chair. 115 V, 60 Hz. Upholstery is in good condition without tears but is discolored.

Features:

• 21 inch wide seat
• seat height raises from 26.5 to 43 inches
• auto return button
• swivel lock pedal
• removable arm boards with wrist cuffs
• restraining strap
• lockout switch
• we can add headrest to make complete unit

Shipping weight is about 600 pounds.

Adjustable height physical therapy table - $875

List: $1,810. MedCon: EX. Treatment table.

Features:

• Movotec hydraulic system; crank raises table height from 25 to 32.25 inches
• 2.25 inch bi-partite pad
• adjustable tilt back support
• one drawer and bottom shelf

Overall dimensions of the unit:

• width: 29.5 in.
• depth: 78
• height: 25

Shipping weight is about 275 pounds each.

Imaging table - $1,675

List: $4,700. MedCon: VG. Fischer C-arm table, model 60700G

Features:

• table height is 34.5 and can be raised to 40.5 by both hand cranks
• hand cranks also used to incline head or feet
• adjustable lumbar support
• steering wheel with hand grip at head end
• clearance between table and lower structural support bar is 31.5 inches
• pad included; 21 x 83.5 x1 inch

Overall dimensions of the unit:

• width: 20.75 in.
• length: 80.5
• height: 34.5

Shipping weight is about 325 pounds.

NMR / Radiolucent table - $1,375

List: $3,200. MedCon: VG. Atomic Products model 240-100 NMR table. May be used for x-ray, C-arm, nuclear medicine, or nuclear magnetic resonance studies.

Features:

• lightweight metal alloy frame
• fixed height 33.5 inches plus 4 inch pad
• 25 x 74 x 4 inch pad
• slots for two patient restraint straps, one strap included

Overall dimensions of the unit:

• width: 26.5 in.
• depth: 74
• height: 39

Shipping weight is about 85 pounds.

Radiolucent imaging table - $1,275

List: $6,250. MedCon: VG. ADC Medical imaging table.

Features:

• adjustable tilt back support
• 75 x 30 x 2 inch pad
• hand crank adjust table height from 33 to 44.5 inches (with pad)
• four locking casters
• transport handle

Overall dimensions of the unit:

• base: 31 x 76 in.
• height: 33

Shipping weight is about 170 pounds.

ENT power procedure chair- $1,750

List: $6,300. MedCon: F. DMI model T223 procedure chair. 115 V, 60 Hz. Good operating condition except swivel lock mechanism needs repair.

Features:

• 19.5 in. wide seat
• seat raises from 23.5 to 39.5 in.
• power control panels on right and left sides of chair
• two preprogrammed positions
• auto return
• calf support and foot rest
• arm rests swing to side and are removable
• lamp with gooseneck
• adjustable height and tilt headrest
• 24 x 24 inch base
• 7 foot power cord with hospital grade plug

Overall dimensions of the unit:

• width: 24 in.
• depth: 35
• height: 51

Shipping weight is about 350 pounds.

Surgical table arm boards and table extension - $975

List: $3,600. MedCon: VG. Surgical table arm boards and table extension, on cart. No manufacturer's label, but possibly Allen.

Features:

• cart can be accessed in the surgical arena for adding arms onto surgical tables
• the two arms shown in the photograph can be unclamped for use on tables
• the two padded arms are 4 x 6 x 1.25 in. and 6 x 20 (tapering at front) x 2 in.
• the retaining rim will accommodate a table extension board

Table extensions features:

• support board is 24 x 15 x 0.25 in., fraying at end of board has been stabilized with tape wrapping
• 2 in. pad attached with Velcro
• clamp tightens onto 1&1/8 inch rail

Overall dimensions of the unit:

• width: 24.5 in.
• depth: 17
• height: 34

Shipping weight is about 100 pounds.

Power surgical table - $5,750 each

List: $17,800. MedCon: VG. Shampaigne 900 surgical table. 115 V, 60 Hz.

Unit is partially radiolucent.

Features:

• rolling base, release lever allows table to be set down on feet
• elevation pedal controls power lift from 31 to 47 in.
• power selector controls back and leg angles, lateral tilt, flex and reflex and Trendelenberg and reverse Trendelenberg
• side railing allows attachment of arm supports or straps
• shipped with a rebuilt back support, and new cushions

flex position and view showing elevation pedal and power movement selector

Shipping weight is about 450 pounds each. 2 matching units in stock.

Surgical table extension - $1,475

List: $4,050. MedCon: VG. Amsco surgical table extension, part number P93896-433

Features:

• platform is 62 inch length and 20 in width (22.5 to rails)
• monopole with T-bar base is 29.5 inches with 22 inch adjustable extension pole and clamp
• Velcro strip for securing pad
• rails for attaching equipment and/or security straps

Shipping weight is about 55 pounds.

Andrews spinal surgical table - $12,750

List: $37,900. MedCon: VG. Andrews spinal surgical table, made by OSI. Used for patient positioning and fixation during spinal surgical procedures. type SST 3000, model 5800.

In overall excellent condition, except one of the patient pads is cracked.

Equipped with dual adjustable arm boards as shown.

Table new in 2005.

Features:

• operated by hydraulic foot pump
• normal/reverse Trendelenberg
• table height up/down
• torso lift, up/down
• foot end, up/down
• lateral tilt, patient's right or left
• tibial support, up/down,
• table top height varies from 32 inches to 48 inches
• 350 pounds patient capacity
• C-arm compatible, in both AP and lateral intra operative views
• patient may be kept in face down prone, or face down kneeling position

Includes the following pads and accessories:

• iliac crest supports
• pads and small accessories, as shown
• table cover

Shipping weight is about 400 pounds.

Radiolucent power surgical table, C-arm compatible - $8,375

List: $62,560. MedCon: refurb. Steirline - Maquet type 1130 02D orthopedic and general procedure power surgical table. Unit needs repairs to radiolucent top, which we will do before shipment.

Unit will be shipped with complete radiolucent top and new pads; in your scheduling, please allow 2 weeks after order for this work to be done.

Features:

• radiolucent top with split leg design
• power height adjust
• power lateral tilt
• power normal/reverse Trendelenberg
• power leg blades
• power lower back adjusts
• power up and back adjust
• table has a flex mode, with a flex/reflex motion
• remote hand control
• operates all power functions off of internal rechargeable batteries
• wired for 100/120 VAC, 50/60 Hz
• height range: 28-43 inches
• base dimensions: 24 x 45 inches

This table is similar to the other Maquet power surgical table that we have, with the addition of the power flex/reflex motion.

Shipping weight is about 450 pounds.

Power exam /manipulation/ treatment table - $1,675

List: $3,470. MedCon: VG. Ritter model 106 power exam table. A large, flat and padded surface for treating patients.

Features:

• electrically adjustable, up/down
• in excellent functional condition
• has 1 tear in upholstery along edge (not visible in photo) about 2 inches long
• moves from a low of about 18 24 inches to a high of about 36 inches above floor
• power operated through foot pedal, as shown
• straps for retaining paper covering role

Shipping weight is about 275 pounds.

Chick- Langren orthopedic surgical operating table - $9,000

List: $109,000. MedCon: EX. Chick orthopedic surgical table, model 10500 CLT, with accessories as shown. May be configured in various ways to perform many procedures. Table has a radiolucent top, may be used may be set up for both portable x-ray and C-arm use.

This table may be used for the following procedures:

• hip pinning, unilateral skin traction
• hip pinning, bilateral skin traction
• imtramedullary nailing, femur, lateral position, skin traction
• imtramedullary nailing, femur, lateral position, skeletal traction
• imtramedullary nailing, Kuntsher position
• imtramedullary nailing, supine position
• imtramedullary nailing, Tibia
• imtramedullary nailing, Humerus
• special procedures
• upper torso
• spinal surgery
• spinal casting
• cervical spine
• full body casting
• lateral canvas yoke technique
• upper extremity casting
• hip spica, pediatric
• hip spica, adult

Some of the basic features of this table are:

• IV hangar
• Pump pedal
• head end floor lock
• foot end floor lock
• lateral tilt control
• A-P cassette tunnel positioning board assembly
• GM boards
• Sacral assembly
• well leg support
• dual bell foot piece traction assemblies
• perineal post
• drapery rods
• top rail lock

overview of true to the upper leg support
overview of foot holder, ankle holder and adjustments
head and of table, showing lateral tilt crank, normal/reverse Trendelenberg hydraulic adjustments, foot pedal, and Castor steer/locking lever
Thigh board
Additional support board
Trunk board, radio lucent, hold 14 x 17 inches film cassette
two additional support fixation devices
cassette holder
a distant additional positioning device, and leg holder
additional IV holder
additional support holder
table extension, fixed on to head of table, 6 feet long, radiolucent
various fixation devices
serial number plate

Shipping weight is about 900 pounds.

Rotabed - $1,975

List: $12,340. MedCon: Ex. Stryker Surgibed "Rota-bed." Supports both top and bottom for patient rotation laterally through 360 degrees. Mounted on hydraulically elevating, normal and reverse Trendelenberg gurney-style base.

For burn and orthopedic treatment, where no axial load is desired on patient limbs.

Shipping weight is about 450 pounds.

Power imaging/surgery table - $4,275

List: $11,300. MedCon: VG. Cone instruments (Northeast medical systems) power surgery and imaging table.

Table adjusts from a height of 26-36 inches.

Features:

• power adjustable elevation, up/down
• power lateral tilt
• power longitudinal tilt, Trendelenberg positioning
• power adjustable backrest
• flip away side rails
• locking casters
• cutout for cardiac ultrasound imaging access

Dimensions:

• length: 76 inches
• width: 25 inches
• height: 26-36 inches

Shipping weight is about 350 pounds.

C-arm / pain management table - $1,475

List: $8,900. MedCon: VG. Herman Engineering, Inc. radiolucent c-arm and pain management table.

Features:

• tripartite 77 x 27 x 2 in. pad (2 minor tears in vinyl)
• adjustable back tilt
• foot rest
• cord organizer

Overall dimensions of the unit:

• width: 78 in.
• depth: 27
• height: 27 ( 6 inch casters maybe added)

Shipping weight is about 175 pounds.

Deluxe ultrasound table - $2,475

List: $8,200. MedCon: VG. Biodex model 056-- 605 deluxe ultrasound table.

Features:

• four locking casters
• adjustable height 28-38 inches
• adjustable angle tilt back support
• folds from a chair into a flat table
• table patient retention straps and leg retention straps
• fold down rails

Shipping weight is about 300 pounds.

Dental/oral surgery chair - $1,675

List: $6,525. MedCon: VG. Vacudent dental/oral surgery chair, model OS 700 pH.

Features:

• power up/down
• power tilt
• power back support adjust
• dual arm boards with retention straps, for IVs, adjustable angle
• adjustable head rest
• return to discharge position button

Dimensions:

• seat width, 19.5 inches
• seat heights, adjusts from 20-32 inches
• base, 20 x 35 inches

Shipping weight is about 275 pounds.

Physical therapy table - $1,975

List: $6,875. MedCon: G. Midland table. 120 V, 60 Hz. Two tears in vinyl as indicated in photo.

Features:

• table height is adjustable from 19 to 37 inches
• remote control for raise and lower
• 9 foot power cord with hospital grade plug
• nose cut out, for when patient is face down on table

Overall dimensions of the unit:

• width: 26.5 in.
• depth: 76.5
• height: 19

Shipping weight is about 200 pounds.

Physical therapy table - $1,850

List: $6,300. MedCon: VG. Akron Therapy Products (HNE Akron) model 8432 tilt chair. 115 V, 60 Hz.

Features:

• back rest swivels (side-to-side arc) and tilts (inclination to either side)
• adjustable leg rests
• nose cut out, for when patient is face down on table
• Hannig activator raises chair by motor from 23 to 41 in. by foot pressure on base bar
• chair moves on casters and sets down on foot pads

Overall dimensions of the unit:

• width: 23 in.
• depth: 76.5
• height: 23

Shipping weight is about 300 pounds.

Physical therapy / manipulation / traction table - $1,375

List: $4,465. MedCon: VG. One of the standard tables for chiropractors, osteopaths and physical therapists.

Henley Tru-Trac model VE-2000 physical therapy table. 115 V, 60 Hz.

Features:

• movable handswitch controls
• hydraulic raise and lower functions
• nose cut out for face down procedures
• adjustable tilt back support

Overall dimensions of the unit:

• width: 77 in.
• depth: 25
• height: min. 17, raises to 35

Shipping weight is about 170 pounds.

Spica fixation orthopedic table - $2,275

List: $6,100. MedCon: G. Orthopedic table, made by Stryker medical. For quick stabilization of orthopedic patients. With accessories as shown.

Features:

• adjustable height
• Trendelenberg
• various attachments adjusts in length and angle

Shipping weight is about 250 lbs.

Oral surgery / maxillofacial / ENT surgery chair - $4,375

List: $14,200. MedCon: ex. Boyd oral surgery maxillofacial and ENT surgery chair, model S-2610.

Features:

• power up/down
• power tilt back support
• power chair tilt (Trendelenberg)
• seat raises from 20 inches to 36 inches high
• Trendelenberg (head down) position
• adjustable arm board, may be used for IV drip lines
• adjustable headrest
• surgical table side rails mounted on both sides of seat base and tilt back support
• emergency stop button
• tapered back of chair permits easy access to neck and head areas of patient
• connection for a hand held remote control, not included.

foot control

• 3 programmable positions
• return to home button
• safety button
• light control
• leg support up/down
• table tilt three programmable position normal/head down
• back support up/down
• table elevation up/down

Shipping weight is about 375 pounds.

Radiolucent imaging table - $2,750

List: $24,700. MedCon: VG. Adjustable height radiolucent gantry bed, may be used for ct, nuclear medicine, C-arm and other units.

This unit was removed from a picker prism 3000 3 head gamma camera. Constructed of steel, all electronic, and a radio lucent graphite composite top.

Overall dimensions of the unit:

• length: 119 in. (This is a 79 in body support and a slide-on 40 in. leg support.)
• width: 15
• height: 32

Shipping weight is about 400 pounds.

Andrews spinal surgical table - $4,750

List: $37,900. MedCon: G. Andrews spinal surgical table, made by OSI. Used for patient positioning and fixation during spinal surgical procedures. type SST 3000, model 5800

Features:

• operated by hydraulic foot pump
• normal/reverse Trendelenberg
• table height up/down
• torso lift, up/down
• foot end, up/down
• lateral tilt, patient's right or left
• tibial support, up/down,
• table top height varies from 32 inches to 48 inches
• 350 pounds patient capacity
• C-arm compatible, in both AP and lateral intra operative views
• patient may be kept in face down prone, or face down kneeling position

Includes the following pads and accessories:

• iliac crest supports
• pads and small accessories, as shown

Shipping weight is about 400 pounds.

ENT surgical procedure chair - $2,375

List: $6,200. MedCon: VG. SMR model Maxi G-2 ENT ear nose and throat surgical procedure and examination chair. in overall excellent condition, both functionally and mechanically, except has a cosmetic issue with wood grain paper on side of chair.

Features:

• power chair up/down
• power recline\upright
• Power backrests back/forward
• adjustable angle head rest
• identical control panels on both sides of chair
• Seat height raises from 19-38 inches
• 25 inch diameter metal base
• wired for 120 volts AC, 60 Hz
• chair has unusual decorative wire brush millwork on both sides of aluminum frame as shown

Shipping weight is about 275 pounds.

Surgical tables, C-arm compatible - $4,750 each

List: $36,700. MedCon: VG. Shampaigne model 1400 surgical table with radio-op top. Radiolucent top on full surgical table. This table may be used for most surgical procedures. It is both portable x-ray and C-arm compatible. New in May, 1985.

Tables features:

• Small control panel, accessible from side and end of table
• roll-around castors with positive floor locking action once table is in position in OR
• All stainless steel construction
• table top moves with 7 degrees of freedom
• Table geometry and design allows full access to patient with a C-arm
• with adjustable angle table extension that may be put in either the foot or head of table
• with standard surgical table side channels for accepting surgical table accessories such as arm boards, kidney supports, stirrups, etc. (not included with table)

Table motions:

• longitudinal slide action (lengthwise), both forward and backward deflections
• lateral tilt, both left and right
• height adjust, up and down
• Trendelenberg and reverse Trendelenberg tilting
• kidney support, up and down
• leg up / down
• back up / down

This is how this table fits a C-arm (patient and C-arm not included)

Click here for details and full pictures.

And, we have a copy of the service manual.

Surgical table extension - $875

List: $1,600. MedCon: G. Radiolucent window, C-arm compatible. Made by Rycor Medical. With flip out, adjustable height support leg. Fits most surgical tables and procedure chairs.

Exterior dimensions:

• length: 52"
• width: 17"

Shipping weight is about 40 pounds.

Spinal surgery frame - $975

List: $4,200. MedCon: VG. Codman Surgical products, spinal surgery frame. Made for Karlin technology. Model 46-3090.

Features:

• 4 locating pegs
• sturdy aluminum frame
• instructions for use printed on unit
• 2 fixed, and 1 adjustable height, pads
• dual clips that fit over surgical table side rail

Exterior dimensions:

• length: 24"
• width: 25"
• height: 30"

Shipping weight is about 50 pounds.

Spinal surgery surgibed - $2,975 each

List: $9,300. MedCon: EX. Stryker model 965 spinal surgery bed. for treatment of spinal surgery patients. Sometimes referred to as a rotabed, used for treatment of patients with burns and orthopedic trauma.

Features:

• height adjusts from 33 inches to 47 inches
• bed d pad 82" x 19"
• 24 inches diameter turning wheel
• security locking pin for wheel, prevents accidental patient rotation
• anterior and posterior frames
• bedpan portal and bedpan holder
• pulley guides for traction device
• 2 side arm boards, each 11 x 10 inches
• units new in 1997
• mattress clamps patient from both top and bottom so they may be turned “elbow over elbow”
• bed rotation permits patient to be easily turned with out having to physically rearrange them on the bed.
• 4 castors with steer/brake/freewheel control lever
• normal/reverse Trendelenberg
• has pulleys on moveable supports on end, so that patient limbs or extremities maybe kept under traction
• under bed storage tray

Overall dimensions:

• length: 99 inches
• width: 29
• height: 48

Shipping weight is about 350 pounds each. 2 units in stock.

Podiatry chair - $1,275

List: $4,900. MedCon: G. Ritter podiatry chair.

Features:

• power up/down
• power functions controlled through hand operated pendant, as shown
• foot rest has tear in upholstery
• power table tilt back
• adjustable power knee support, as shown in photos

Shipping weight is about 300 pounds.

Imaging/ ultrasound/ OBGYN chair - $1,475 each

List: $4,865. MedCon: EX. Atomic Products model 056-605 imaging and ultrasound chair. Functions as either a chair, or lays completely flat to be a table.

Features:

• table is hydraulically adjustable up/down
• drop away leg section, adjustable angle
• accepts folding side rails, not included
• contoured tabletop design, narrow stem 19 inches wide four probe accepts
• adjustable Fowler back support, manually adjusted in five increments
• place for IV pole
• accepts optional stirrups
• four locking castors
• base of table is shaped to maneuver around other equipment

4 matching units in stock.

Shipping weight is approximately 300 pounds each.

OB/GYN delivery/surgical table - $2,750

List: $11,220. MedCon: G. Shampaigne model 2605 labor and delivery table.

Used for labor and OBGYN surgical procedures, specifically C-sections cesarean sections.

Features:

• pull out support in leg area hidden base in for fluids
• patient hand pull bars
• clamps for stirrups
• adjustable tilt back support
• normal/reverse Trendelenberg
• break/lock lever
• hydraulic up/down

Shipping weight is about 300 pounds.

Power tilt table - $1,475

List: $6,200. MedCon: EX. Vertical / horizontal power tilt table. Tables go from full vertical to full horizontal. In this way, patients who can not kneel can hold themselves into table. Made by Tri wg.

Features:

• patient grip bar
• down table support leg
• retention straps
• power hand control

Power hand control is situated so that patient may operate table themselves.

Shipping weight is about 200 pounds.

Visual stimulation chair and stool - $975 the pair

List: $2,300. MedCon: VG. Visual stimulation chair, and physicians stool. patient chair features a back support at a head rest. This chair provides a resting place for a patient undergoing visual stimuli testing, such as used in ENT or neurology offices.

Upholstery on stool and chair match each other.

Shipping weight is approximately 275 lbs.

Traction table - $575

List: $1800. MedCon: F. In good functional condition, however upholstery is in poor condition. Table splits in middle, allowing one half of the table to move longitudinally in relation to the other half of the table. For chiropractic and back adjustment procedures.

shipping weight is about 150 lbs.

Traction table - $975

List: $2350. MedCon: VG. Tru-Trac traction and therapy table, made by traction specialties. Used for traction procedures, chiropractic and osteopathic manipulations. one half of the table slides longitudinally in relation to the other half of the table. With face cut out.

Shipping weight is about 200 lbs.

Stainless surgical instrument table - $600

List: $1,500. MedCon: VG. Stainless steel table, with bend in middle.

About 5 feet wide overall. 30 degree angel deflection in middle.

Shipping weight is about 100 pounds.

Pathology dissection table - $575

List: $1,800. MedCon: G. Specimen dissection table. All stainless steel construction. Has a slit depression in center of table, so that fluid spilled onto table drain through central drain.

Exterior dimensions:

• length: 48"
• width: 26"
• height: 30"

Shipping weight is about 125 pounds.

Tilt back procedure chair - $2,475

List: $7,300. MedCon: G. Hill rom procedural recliner chair.

Features:

• blue upholstery
• arm rests on both sides of chair go down
• tilt back design, with swing up leg support
• position bar in back of chair
• netting on chair back for small item storage
• hydraulic up / down motion, operated by foot pedal

Exterior dimensions:

• length: 78"
• width: 31"
• height: 25 - 54"

Shipping weight is about 275 pounds.

Surgical table leg holder - $975 each

List: $2,475. MedCon: VG. Surgical table leg holder. Fits into side rail clamp on a surgical table, and holds a patient's leg securely and firmly. Adjustable width.

2 units in stock.

Shipping weight is about 40 pounds each.

Manipulation and treatment tables - $975

List: $2,250. MedCon: G. Manipulation tables, as used by osteopaths and chiropractors. Each table is electric up and down adjustable. one uses a foot control, the other switch on the side of the table

Exterior dimensions:

• length: 79"
• width: 28"
• height: 22" when down

Shipping weight is about 250 pounds.

Orthopedic surgical table - $7,500

List: $27,370. MedCon: VG. Chick model 2001 CST orthopedic surgical table. The geometry of the table allows enough room for access to a C-arm to adequately image the upper leg, partial lower leg, full abdomen and complete lower chest of the patient. In this way a fracture or other orthopedic work may be performed, and image taken, and adjustments made accordingly while the patient is on the table.

Click here for complete pictures.

Surgical table radiolucent top - $900

List: $2,500. MedCon: G. X-ray transparent top for Amsco 1080 or 2080 surgical tables.

Does not include surgical table. Enables use of portable X-ray with normal surgical table.

Table and gurney accessories

• MedCon: EX. Collapsible 2 place IV pole, also tilts down, on side channel clamp. Midmark s/n TO16287 and TO16612. 2 in stock. $275 each
• MedCon: N. Clip on seat cushion, brown, probably Midmark, $85
• MedCon: EX. Arm rests. Clamp to side of channel, clamp mechanism is integral to arm support. 5 pair in stock. Red brown, brown and 2 tone, pink over white plastic. Midmark, s/n TO11147 and others. $325 per pair.
• MedCon: N. Hausted, threaded pole for gurney, about 18" long, stainless, 12 in stock - $25 each
• MedCon: N. IV pole bracket, built into end bumper for gurney. Hausted, 7 in stock - $45 each
• MedCon: N. Amsco 1080 channel clamps, 2 in stock, $75 each
• MedCon: VG. Surgical table stirrups, Amsco and others, for orthopedic, surgical and other tables. Stirrups are adjustable in length, with back of knee support. 9 in stock, $375 per pair
• MedCon: EX. Leg supports, Hillrom adjustable leg pad with holder, $175 / pair
• MedCon: EX. Midmark knee support, small, with table clamps. $325 / pair
• MedCon: EX. Lock in stirrups OBGYN style, for gurney. Looks similar to exam table OBGYN type stirrups, with adjustable pin clamps. 3 pair in stock, $225 / pair.
• MedCon: F. Leg stirrups for Hydra adjust and other urology tables, no clamps, adjustable and an rotation. Probably Liebel Flarsheim. $95 / leg.
• MedCon: EX. 4 sets leg stirrups for Hillrom birthing bed, with adjustable support. $375 per pair

© Copyright 1993 - 2013 by Production Engineering. PEMED® is a registered trademark of Production Engineering. MedCon is also a trademark of Production Engineering. All rights reserved. Contact PEMED for license requests. The usual copyright notices and disclaimers. Except for search engines or link listing, no part of this website, including derived information, may be republished without express written permission and payment of fees.

Production Engineering - Medical Equipment Division

Surgicaltable.com

6035 E. 38th Avenue, Denver, Colorado 80207 USA (303) 393-7800 FAX (303) 393-1482